RLYR6001-I系列熱風拉幅定型機采用鑄造成型軌道、加油潤滑，適用于真絲、毛麻、棉、化纖等機織物的拉幅和熱定型。
　　本機采用交流變頻技術，PLC控制變頻同步調速，實現了各主動單元同步精確和主要工藝參數在線監控。故障顯示功能可以讓用戶及時、準確地排除故障，以達到最少的停機時間，創造最大的生產效益。
　　RLYR6001-I series stenter mashine is applicable to tentering and hotsetting of the machine-woven fabrics of naturics of natural silk,cotton ,wool and jute,etc.
　　This machine applies an AC frequency-conversion technique and PLC to have an in-process supervision and control for a precise synchronous movement of every active element and over the main techchnological parameters.Its abnormal problems timely and precisely,therefore,to minimize the machine stop time and maximize the production efficiency.

設備流程：
　　平幅進布→緊布架→平移（擴福）對中→二輥斜軋車→張力傳感裝置→圓盤整緯→平移對中→下超喂→機械整緯→螺紋擴福→上超喂→剝邊→紅外探邊→毛刷上針&r

Working procedure of the equipment：
　　Open width fabric-infeeding→fabric tensioner→translation(expander) centering→two-rollmangling machine→tension sensor device→disc straightener→traighlation centering→lower overfeed→mechanical straightener→spiral expabder→upper over-feed→rip-off selvedge→ultrared rayedge detector→rip-off upper needles→heat-setting→cold air cooling→fabric-swinng collection or rolling-collection

該機器在2011第十五屆上海國際紡織工業展展出

技術參數：
　　◆車別：左手或右手

◆公稱門幅：2000~3600mm

◆有效門幅：1800~(w-200)mm

◆設計車速：Max.110m/min

◆傳動方式：多單元交流電機變頻器同步調速傳動，出布區電視監控，觸摸屏電腦控制工藝參數。

◆超喂量：上針超喂調整調整范圍大（-10%~+60%）,適合各種織物的不同超喂率，左右布邊張力可分別設定。

◆持布方式：針鋏/布鋏

◆烘房溫度：220゜C（max）

◆壓縮空氣壓力：0.4-0.5MPa

◆外形尺寸：長（20520+N×3000）mm/寬（W+2200）

◆裝機容量：（N×15+57.37）kw（標準配置）

◆熱源：載熱油/天燃?xì)?電

◆能源消耗：100萬大卡

注：N為烘房數量，W為門幅寬度

Technical specification：

◆Machine type:left hand or right hand

◆Nominal width:2000～3600mm

◆Effective width:1800～(w-200)mm

◆Designed running speed:Max.110m/min

◆Way oftransmission:Synchronous speed-regulateable tansmisson by AC motor and frequency converter.TV monitoring for the fabric-out area.The finger-touch screen for a computerzed technological parameter control.

◆Over-feed amount:Big adjustment range for the upper needle overfeed (-10%to+60%),applicable to whatever kind fabric with different over-feed rates.The lefe and right fabric edgetensions can be set respectively.

◆Fblic holding method:Needle clip/fabric clip/needle-fabric bipurpose clip

◆Drying tunnel temperature:220゜C(max)

◆Compressed air pressure 0.4-0.5

◆Outside dimension:L(17606+N×3000)mm/W(W+2200)mm/H4000 mm

◆Insatallation capacity:(N×15+57.37)kw

◆Heat source:Thermal conductve oil/natural gas/electricity

◆Energy consumption:1million kilocalorie

Note:N is the drying tunnel number.W is the fabric width.

展臺照片：